Home|Product Center|Industrial & Food Hose|SAE 100R6 HYDRAULIC HOSE

SAE 100R6 HYDRAULIC HOSE

OIL & FUEL · SAE 100R6 · 1 layer of high-strength polyester cord braid · 20 bar working / 60 bar burst

Hose Construction
Structure:Inner Tube: NBR (Nitrile Butadiene Rubber) /
Reinforcement:1 layer of high-strength polyester cord braid /
Cover:NBR + CR (Nitrile Butadiene Rubber + Chloroprene Rubber)
Hose Features
Bend Radius:Down to 60–190 mm minimum bend radius.
Pressure Rating:20 bar working against 60 bar minimum burst — a 3.0× margin.
Size Coverage:7 codes in the table, 6–19 mm bore, from 6 upward.
Mass Per Metre:From 0.18 to 0.55 kg/m depending on bore .
Application:SAE 100R6 HYDRAULIC HOSE — Industrial & Food Hose.

Online consultation Leave a message

24 Hours Service Hotline

+86 137 2136 0724

CONDUCTIVE CHEMICAL SUCTION AND DISCHARGE HOSE

Data Display

INNER DIAMETER I.D. (mm)	INNER DIAMETER I.D. (inch)	OUTER DIAMETER O.D. (mm)	WORKING PRESSURE W.P (psi)	WORKING PRESSURE W.P (bar)	psi	BURST PRESSURE B.P. (psi)	BURST PRESSURE B.P. (bar)	psi	BENDING RADIUS B.R. (mm)	WEIGHT (kg/m)	LENGTH (ft)	LENGTH (m)
6	1/4"	14	300	20	290	900	60	870	60	0.18	328	100
8	5/16"	16	300	20	290	900	60	870	80	0.21	328	100
10	3/8"	18	300	20	290	900	60	870	100	0.25	328	100
13	1/2"	22	300	20	290	900	60	870	130	0.36	328	100
16	5/8"	26	300	20	290	900	60	870	160	0.48	328	100
19	3/4"	29	300	20	290	900	60	870	190	0.55	328	100
Note: Other technical data can be customized on request.

Values are reproduced from the official YIBO product page. psi columns = MPa × 145.038, rounded. Across the 7 codes the top rating is 20 bar working / 60 bar minimum burst; the order data sheet governs the batch.

⬇ Download Datasheet (PDF)

Application & Selection

SAE 100R6 HYDRAULIC HOSE — Industrial & Food Hose. Widely used in hydraulic systems of mechanical equipment, suitable for fluids with an aromatic hydrocarb. SAE 100R6 HYDRAULIC HOSE covers 6–19 mm across 7 published codes.

SAE 100R6 HYDRAULIC HOSE carries a published 20 bar working, 60 bar minimum burst rating. Plan the supports around 0.18–0.55 kg/m per metre. SAE 100R6 HYDRAULIC HOSE assemblies ship crimped and pressure-tested, with metric / BSP / JIC / ORFS ends. SAE 100R6 HYDRAULIC HOSE runs roughly 20 days from confirmation over its 7 codes, with OEM marking and packing.

Inside the YIBO Hose Factory · Where this line runs: 7 codes, 6–19 mm bore, braided or spiral-wound and burst-tested on one floor.

Frequently Asked Questions

What bore sizes does SAE 100R6 HYDRAULIC HOSE cover?

SAE 100R6 HYDRAULIC HOSE is published in 7 codes spanning 6–19 mm nominal bore, from 6 upward. 7 rows over the 6–19 mm bore band, each with its own pressure and mass.

What is the working pressure of SAE 100R6 HYDRAULIC HOSE?

SAE 100R6 HYDRAULIC HOSE carries a published 20 bar working, 60 bar minimum burst rating. Sizing: step through the 6–19 mm bore column, 7 codes in all.

What is the MOQ on SAE 100R6 HYDRAULIC HOSE?

SAE 100R6 HYDRAULIC HOSE starts at 100 m across the 6–19 mm band; free samples come off the same run.

What is the production lead time on SAE 100R6 HYDRAULIC HOSE, and can it carry our brand?

Allow roughly 20 days to dispatch SAE 100R6 HYDRAULIC HOSE, covering the 6–19 mm band. SAE 100R6 HYDRAULIC HOSE assemblies ship crimped and pressure-tested, with metric / BSP / JIC / ORFS ends.