Home|Product Center|Steel Wire Braided Hydraulic Hose|FIBER REINFORCED HIGH PRESSURE RESIN HOSE

FIBER REINFORCED HIGH PRESSURE RESIN HOSE

OIL & FUEL · HIGH PRESSURE · 274 bar working / 1096 bar burst

Hose Construction
Structure:The Hose Consists of a Nylon Inner Tube, One or Two Layers of Fiber Braiding, and a Polyurethane Outer Cover
Working Temperature:-40℃ to +100℃; for Water Medium: -40℃ to +70℃.
Hose Features
Bend Radius:Routes down to 35–256 mm minimum radius depending on bore, with every code listed individually so tight machine bays can be planned.
Pressure Rating:Rated 274 bar working with 1,096 bar minimum burst: a 4.0× safety margin, quoted per code in the table below.
Size Coverage:13 published codes spanning 5 mm to 25 mm bore, from R7-3-05 upward .
Application:Suitable for Conveying Hydraulic Fluids Such as Alcohol, Hydraulic Oil, Lubricating Oil, Emulsions, Water, and Air, Etc
Outer Diameter:Outer diameter 10.3–34 mm across the published bores.

Online consultation Leave a message

24 Hours Service Hotline

+86 137 2136 0724

COMPACT SINGLE WIRE BRAID HYDRAULIC HOSE

Data Display

FIBER REINFORCED HIGH PRESSURE RESIN HOSE

PRODUCT NAME	NOMINAL BORE (mm)	SPECIFICATION (inch)	INSIDE DIAMETER （ID）mm (min)	OUTSIDE DIAMETER （OD）mm (max)	MAXIMUM WORKING PRESSURE W.P (Mpa)	psi	MINIMUM BURST PRESSURE B.P (Mpa)	psi	MINIMUM BEND RADIUS Min.B.R (mm)
R7-3-05	5	3/16“	4.6	10.3	21.0	3,046	84	12,183	35
R7-4-06	6	1/4“	6.1	12.7	22.5	3,263	90	13,053	50
R7-5-08	8	5/16”	7.9	14.3	19.0	2,756	76	11,023	50
R7-6-10	10	3/8“	10.3	15.9	17.5	2,538	70	10,153	80
R7-8-12.5	12.5	1/2“	12.7	19.8	14.0	2,031	56	8,122	100
R7-3-05	5	3/16”	4.6	10.3	25.0	3,626	100	14,504	55
R7-4-06	6	1/4“	6.1	13.3	27.4	3,974	109.6	15,896	75
R7-5-08	8	5/16”	7.9	15.0	26.0	3,771	104	15,084	85
R7-6-10	10	3/8“	10.3	18.0	25.0	3,626	100	14,504	100
R7-8-12.5	12.5	1/2”	12.7	21.6	21.0	3,046	84	12,183	140
R7-10-16	16	5/8“	15.9	23.6	16.0	2,321	64	9,282	165
R7-12-19	19	3/4”	19.0	26.4	14.0	2,031	56	8,122	195
R7-16-25	25	1“	25.4	34	10.5	1,523	42	6,092	256

Values are reproduced from the official YIBO product page. psi columns = MPa × 145.038, rounded. 13 codes from 5 mm to 25 mm bore — the top rating is not the whole story; the order data sheet governs the batch.

⬇ Download Datasheet (PDF)

Application & Selection

FIBER REINFORCED HIGH PRESSURE RESIN HOSE — R7 — Braided Hydraulic Hose. SUITABLE FOR CONVEYING HYDRAULIC FLUIDS SUCH AS ALCOHOL, HYDRAULIC OIL, LUBRICATIN. FIBER REINFORCED HIGH PRESSURE RESIN HOSE is published in 13 codes spanning 5–25 mm bore.

Working and burst rating of FIBER REINFORCED HIGH PRESSURE RESIN HOSE peak at 274 / 1,096 bar, a 4:1 margin. Metric / BSP / JIC / ORFS ends are crimped and pressure-tested in-house, outside diameter 10.3–34 mm. Allow about 20 days for FIBER REINFORCED HIGH PRESSURE RESIN HOSE across the 5–25 mm band, OEM branding included.

Inside the YIBO Hose Factory · Where this line runs: 13 codes, 5–25 mm bore, braided or spiral-wound and burst-tested on one floor.

Frequently Asked Questions

What bore sizes does FIBER REINFORCED HIGH PRESSURE RESIN HOSE cover?

FIBER REINFORCED HIGH PRESSURE RESIN HOSE is published in 13 codes spanning 5–25 mm nominal bore, from R7-3-05 upward. 13 rows over the 5–25 mm bore band, each with its own pressure and mass.

What is the working pressure of FIBER REINFORCED HIGH PRESSURE RESIN HOSE?

Working and burst rating of FIBER REINFORCED HIGH PRESSURE RESIN HOSE peak at 274 / 1,096 bar, a 4:1 margin. Sizing: read the 13 rows over 5–25 mm against your own circuit rather than the range maximum.

Is there a minimum order for FIBER REINFORCED HIGH PRESSURE RESIN HOSE?

Standard items of FIBER REINFORCED HIGH PRESSURE RESIN HOSE start from 100 m, covering every code in the 5–25 mm band; free samples are available so the quality can be checked against your medium before you commit to volume.

What is the production lead time on FIBER REINFORCED HIGH PRESSURE RESIN HOSE, and can it carry our brand?

Allow roughly 20 days to dispatch FIBER REINFORCED HIGH PRESSURE RESIN HOSE, covering the 5–25 mm band. Metric / BSP / JIC / ORFS ends are crimped and pressure-tested in-house, outside diameter 10.3–34 mm.