Home|Product Center|Application Page|Hydraulic Hose for Agricultural Machinery

Hydraulic Hose for Agricultural Machinery

FACTORY DIRECT · ISO 9001 · OEM AVAILABLE · 415 bar working / 1660 bar burst · 4.6–10.1 mm

Published Range
Nominal bore:4.6–10.1 mm
Max working pressure:415 bar
Min burst pressure:1660 bar
Mass per metre:0.33–0.6 kg/m.
Size range:4 codes in the table, from 2SN-03-05 upward
Hose Features
Bend Radius:Minimum bend radius 90–130 mm .
Duty-Cycle Matched:The construction is chosen against how hard the machine actually works, not against a catalogue default.
Failure Mode First:We start from what normally fails on this equipment, then specify the hose that resists it.
Tested Under Pressure:Working and burst pressure are verified in our own laboratory before shipment.
Application:Farm machinery has a duty cycle nobody else has: intense use for a few weeks, then months parked in a shed.

Online consultation Leave a message

24 Hours Service Hotline

+86 137 2136 0724

COMPACT SINGLE WIRE BRAID HYDRAULIC HOSE

Data Display

Farm machinery has a duty cycle nobody else has: intense use for a few weeks, then months parked in a shed.

PRODUCT NAME	NOMINAL INNER DIAMETER (mm)	SPECIFICATION (inch)	INNER DIAMETER （ID）mm (min)	INNER DIAMETER （ID）mm (max)	REINFORCEMENT LAYER OUTER DIAMETER （W.D）mm (min)	REINFORCEMENT LAYER OUTER DIAMETER （W.D）mm (max)	OUTER DIAMETER （OD）mm (max)	MAXIMUM WORKING PRESSURE W.P (Mpa)	psi	MINIMUM BURST PRESSURE B.P (Mpa)	psi	MINIMUM BENDING RADIUS Min.B.R (mm)	REFERENCE WEIGHT W.T (Kg/m)
2SN-03-05	5	3/16“	4.6	5.4	10.6	11.7	16	41.5	6,019	166.0	24,076	90.0	0.33
2SN-04-06	6.3	1/4”	6.2	7.0	12.1	13.3	17.7	40.0	5,802	160.0	23,206	100.0	0.42
2SN-05-08	8	5/16“	7.7	8.5	13.7	14.9	19.4	35.0	5,076	140.0	20,305	115.0	0.47
2SN-06-10	10	3/8”	9.3	10.1	16.1	17.3	21.7	33.0	4,786	132.0	19,145	130.0	0.6

Values are reproduced from the official YIBO product page. Hydraulic Hose for Agricultural Machinery: psi columns = MPa × 145.038, rounded. Hydraulic Hose for Agricultural Machinery: 4 codes from 4.6 mm to 10.1 mm bore — the top rating is not the whole story; the order data sheet governs the batch.

⬇ Download Datasheet (PDF)

Application & Selection

Farm machinery has a duty cycle nobody else has: intense use for a few weeks, then months parked in a shed. Hydraulic Hose for Agricultural Machinery covers 4.6–10.1 mm across 4 published codes.

Working and burst rating of Hydraulic Hose for Agricultural Machinery peak at 415 / 1,660 bar, a 4:1 margin. Hydraulic Hose for Agricultural Machinery: Mass is published at 0.33–0.6 kg/m per metre. Hydraulic Hose for Agricultural Machinery: Metric / BSP / JIC / ORFS ends are crimped and pressure-tested in-house across the 4.6–10.1 mm bore. Allow about 20 days for Hydraulic Hose for Agricultural Machinery across the 4.6–10.1 mm band, OEM branding included.

Inside the YIBO Hose Factory Hydraulic Hose for Agricultural Machinery: · The line behind the 2SN-03-05 code — winding, crimping and burst testing on one floor.

Frequently Asked Questions

What bore sizes does Hydraulic Hose for Agricultural Machinery cover?

Hydraulic Hose for Agricultural Machinery is published in 4 codes spanning 5–10 mm nominal bore, from 2SN-03-05 upward. Hydraulic Hose for Agricultural Machinery: 4 codes across 4.6–10.1 mm, row by row.

What is the working pressure of Hydraulic Hose for Agricultural Machinery?

Working and burst rating of Hydraulic Hose for Agricultural Machinery peak at 415 / 1,660 bar, a 4:1 margin. Hydraulic Hose for Agricultural Machinery: Sizing: read the 4 rows over 4.6–10.1 mm against your own circuit rather than the range maximum.

Is there a minimum order for Hydraulic Hose for Agricultural Machinery?

Hydraulic Hose for Agricultural Machinery starts at 100 m across the 5–10 mm band; free samples come off the same run.

What is the production lead time on Hydraulic Hose for Agricultural Machinery, and can it carry our brand?

Hydraulic Hose for Agricultural Machinery production runs about 20 days from confirmation, across the 5–10 mm band. Hydraulic Hose for Agricultural Machinery: Metric / BSP / JIC / ORFS ends are crimped and pressure-tested in-house across the 4.6–10.1 mm bore.