Home|Product Center|Liquid Cooling Hose|DATA CENTER LIQUID COOLING HOSE

DATA CENTER LIQUID COOLING HOSE

HIGH WEAR RESISTANT · UV / OZONE RESISTANT · 1 or 2 layers of synthetic fiber braid · 13.8 bar working / 55 bar burst

Published Range
Nominal bore:6.1–32.8 mm
Max working pressure:13.8 bar
Min burst pressure:55 bar
Mass per metre:0.13–0.7 kg/m.
Hose Features
Bend Radius:Minimum bend radius 24.5–195 mm .
Inner Tube:Black EPDM synthetic rubber
Reinforcement:1 or 2 layers of synthetic fiber braid reinforcement
Cover:Black EPDM synthetic rubber with weather, abrasion, ozone resistance, and V0 flame retardancy
Application:DATA CENTER LIQUID COOLING HOSE — Data Center Liquid Cooling Hose — full specification table, PDF datasheet and factory-direct supply.

Online consultation Leave a message

24 Hours Service Hotline

+86 137 2136 0724

CONDUCTIVE CHEMICAL SUCTION AND DISCHARGE HOSE

Data Display

DATA CENTER LIQUID COOLING HOSE — Data Center Liquid Cooling Hose — full specification table, PDF datasheet and factory-direct supply.

SPECIFICATION (inch)	HOSE INNER DIAMETER （I.D）mm (min)	HOSE INNER DIAMETER （I.D）mm (max)	HOSE OUTER DIAMETER （O.D）mm (min)	HOSE OUTER DIAMETER （O.D）mm (max)	MAXIMUM WORKING PRESSURE Max.W.P (MPa) (MPa)	psi	MINIMUM BURST PRESSURE Min.B.P (MPa) (MPa)	psi	MINIMUM BENDING RADIUS Min.B.R (mm) (mm)	REFERENCE WEIGHT W.T (kg/m) (kg/m)
1/4"	6.1	7.2	11.6	12.6	1.38	200	5.5	798	24.5	0.13
5/16"	7.7	8.3	14.5	15.5	1.38	200	5.5	798	31.5	0.18
3/8"	9.5	10.3	15.4	16.4	1.38	200	5.5	798	37	0.19
1/2"	12.5	13.3	19.7	20.7	1	145	1	145	69	0.25
5/8"	15.8	16.6	22.5	23.7	1	145	1	145	88	0.30
3/4"	18.8	19.6	26.4	27.6	1	145	1	145	113	0.35
1"	25.2	26.2	33.6	34.8	1	145	1	145	143	0.52
1 1/4"	31.8	32.8	43	44.6	1	145	1	145	195	0.70

Values are reproduced from the official YIBO product page. psi columns = MPa × 145.038, rounded. Ratings run to 13.8 bar working / 55 bar minimum burst over the 6.1–32.8 mm bore band; the order data sheet governs the batch.

⬇ Download Datasheet (PDF)

Application & Selection

DATA CENTER LIQUID COOLING HOSE — Data Center Liquid Cooling Hose — full specification table, PDF datasheet and factory-direct supply. DATA CENTER LIQUID COOLING HOSE covers 6.1–32.8 mm across 8 published codes.

DATA CENTER LIQUID COOLING HOSE tops out at 13.8 bar working over its 8 codes. This series weighs 0.13–0.7 kg/m. Assemblies are crimped and pressure-tested in-house, metric / BSP / JIC / ORFS ends, across the 8 codes in the 6.1–32.8 mm band. Smallest order of DATA CENTER LIQUID COOLING HOSE: 100 m, covering its 8 codes.

Inside the YIBO Hose Factory · 8 codes over 6.1–32.8 mm bore, built and tested here on one shop floor.

Frequently Asked Questions

What bore sizes does DATA CENTER LIQUID COOLING HOSE cover?

DATA CENTER LIQUID COOLING HOSE is published in 8 codes spanning 6.1–31.8 mm nominal bore, from 1/4" upward. 8 codes, 6.1–32.8 mm bore at 0.13–0.7 kg/m, all taken from the table.

What is the working pressure of DATA CENTER LIQUID COOLING HOSE?

DATA CENTER LIQUID COOLING HOSE tops out at 13.8 bar working over its 8 codes. Sizing: read the 8 rows over 6.1–32.8 mm against your own circuit rather than the range maximum.

What is the minimum order quantity for DATA CENTER LIQUID COOLING HOSE?

The minimum on standard DATA CENTER LIQUID COOLING HOSE is 100 m and it applies to every code in the 6.1–31.8 mm band. Cut a free sample of DATA CENTER LIQUID COOLING HOSE from the production run before committing to volume.

What is the production lead time on DATA CENTER LIQUID COOLING HOSE, and can it carry our brand?

Lead time for DATA CENTER LIQUID COOLING HOSE is around 20 days from order confirmation depending on quantity, and it covers every code in the 6.1–31.8 mm band. Assemblies are crimped and pressure-tested in-house, metric / BSP / JIC / ORFS ends, across the 8 codes in the 6.1–32.8 mm band.